Matek ELRS-R24-P6 Receiver

AVAILABILITY: In Stock (6 items)


6 in stock

  •  Delivery & Return

    Domestic Shipping

    • Estimate Domestic delivery options can be calculated at the Shopping Cart.
    • Home delivery orders are delivered on weekdays by Australia Post.
    • 4 - 7 business days for delivery to metro locations.
    • 7 - 10 business days to regional locations including WA, QLD and NT.
    • This delivery time frame is subject to changes in circumstances.
    • All orders dispatched within 2 to 3 business days.
    • See the Delivery Policy for details on shipping methods, costs and delivery times.

    International Shipping

    • Estimate International delivery options can be calculated at the Shopping Cart.
    • International Orders will be shipped via Australia Post.
    • Any customs or import duties and associate fees may impose on your destination country.

    Returns And Exchanges

    • Replacemnet warranty only cover for items that are Dead On Arrival (DOA).
    • 7 days return policy for all unopened items.
    • See conditions and procedure in our Returns Policy.
  •  Ask a Question


The MATEKSYS ELRS-R24-P6 is a PWM receiver with a 2.4GHz frequency and ExpressLRS 3.0 firmware.


  • ExpressLRS 3.0 firmware
  • 2.4GHz Frequency
  • 6 PWM Outputs


  • ESP8285, SX1281
  • Antenna connector: IPEX MHF 1
  • 6 x PWM outputs
  • Support 2~8S VBat voltage sense
  • RF Frequency: 2.4GHz (2400~2480MHz)
  • Telemetry power: 12dbm
  • Receiver output protocol: PWM
  • Input voltage: 4~9V DC @ “+” pad
  • Voltage sense: 34V Max. @ “VBat” pad
  • Power dissipation:  45mA(binding), 85mA(wifi mode)
  • PCB size: 20mm x 18mm
  • Weight: 2g w/ antenna


  • 1x ELRS-R24-P6
  • 1x IPEX MHF1 Antennas. 15cm
  • Dupont 2.54 pins (Board is shipped unsoldered)


  • ExpressLRS 3.0 or newer,   DIY 2.4 GHz / DIY 2400 RX PWMP EX
  • ExpressLRS wiki for PWM receiver, Click HERE
  • Make sure Receiver and TX module both are running ExpressLRS 3.0 or newer


  • Receiver has ExpressLRS 3.0 preloaded with binding phrase “123456”,  the Receiver will never enter binding mode if using the traditional binding procedure.
  • You need to reflash it with your binding phrase OR go into WebUI to set your binding phrase.

Flashing via Wifi

  • Disconnect ESC and servos from receiver first.
  • Power on receiver by 5V source. Receiver’s LED(Red) will blink slow at first, and after 20s, it should blink fast indicating it’s on Wifi Hotspot Mode.
  • More detailed steps,  pls refer this page.
  • Target: DIY 2.4 GHz / DIY 2400 RX PWMP EX

Flashing via UART

  1. Disconnect ESC and servos from receiver first.
  2. Wire the receiver into the USB-TTL adapter, with TX on receiver connected to the Rx on the USB-TTL, and RX on receiver connected to the Tx of the USB-TTL. Wire 5V and GND of the USB-TTL to 5V and GND of the Receiver.
  3. Press the boot button while powering on the receiver, then release – the Red LED on receiver should now be solid.
  4. Select the target DIY 2.4 GHz / DIY 2400 RX PWMP EX and “UART” for Flashing Method,  set your bind phrase and Firmware Options and once done, click on Build and Flash.

Based on 0 reviews

0.00 Overall
Be the first to review “Matek ELRS-R24-P6 Receiver”

Your email address will not be published. Required fields are marked *


There are no reviews yet.

SKU: ELRS-R24-P6 Categories: , Tags: ,
My Cart
ELRS-R24-P6 Receiver

Matek ELRS-R24-P6 Receiver


Ask a Question