Hot
New
In Stock
Pre-order
Out Of Stock

Holybro Kakute F4 V2.3 Flight Controller

AVAILABILITY: In stock (6 items)

VENDOR: Holybro

$52.60

YOU ARE $150.00 AWAY FROM FREE STANDARD AU SHIPPING
PRODUCT INFORMATION
Specifications
Manual
CUSTOMER REVIEWS
PRODUCT INFORMATION

The Holybro Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. The faster F4 processor gives room for future feature development: run all features at the fast 8 kHz PID loop rate, at single-digit CPU utilization! Because of issues with serial inversion, other F4 boards struggle to support protocols such as FrSky SBUS and SmartPort at the same time. The Kakute F4 is designed to support all serial protocols at once.

Features
  • Supports Betaflight and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.
  • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
  • Automatic voltage monitoring. No need to run a separate vat wire for voltage monitoring; the Kakute F4 V2mini monitors voltage directly from the battery power lead.
  • On-board regulators output 5v at up to 1.0 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • On-board regulators output 9v at up to 2A to power DJI VTX.
  • 6 PIN JST GH connector for DJI VTX.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.
  • 2 Additional PWM outputs, can be used for Camera control, motor5, or motor6 after resourced.

Pinout Diagram

Kakute F4 V2.3 Pinout Diagram

Specifications
Kakute F4 V2.3
  • MCU: STM32F405RGT6 32-bit processor
  • IMU: MPU6000 (SPI)
  • Barometer: BMP280
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 5 hardware UARTS (UART1,2,3,4,6)
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported
  • 128 Mbit Dataflash chip for Blackbox logging
  • Dimensions: 36.8 x 36.8 x 8mm
  • Mounting Holes: 30.5 x 30.5mm (M4)
  • Weight: 7.4g

Content Included
  • 1 x FC board
  • 4 x M3 Anti-Vibration Silicone Grommet Insert
  • 1 x JST SH 8pin 150mm cable
  • 1 x JST SH 6pin to GH 8pin 150mm cable ( The cable that goes to the DJI Air Unit is included.)
  • 1 x JST SH 6pin to GH 8pin 80mm cable ( The cable that goes to the DJI Air Unit is included.)
Manual
CUSTOMER REVIEWS

This is a standard cookie notice which you can easily adapt or disable as you like in the admin. We use cookies to ensure that we give you the best experience on our website.

Holybro Kakute F4 V2.3 Flight Controller

Holybro Kakute F4 V2.3 Flight Controller

$52.60
Pre-loader